What's that rattle?!

Moderators:Popsjag, J44EAG

charlier6790

Member
Posts:39
Joined:Sun Mar 01, 2009 12:00 pm
Location:Hereford
What's that rattle?!

Postby charlier6790 » Thu May 17, 2018 11:22 am

On bumpy roads I've got an annoying rattle from the front (N/S/F, I think) of my X350R. My garage assures me that the suspension and anti-roll bar bushes are all fine so I guess it must be something else. I've heard of issues with riveted aluminium panels at the front of these cars coming loose. Could it be that - or something else? Any thoughts or advice would be much appreciated. Many thanks. Charlie

User avatar
BrianG

Member
Posts:461
Joined:Sat Nov 22, 2008 4:23 pm
Location:West Sussex

Re: What's that rattle?!

Postby BrianG » Thu May 17, 2018 1:23 pm

I suggest you check for missing/broken anti-rattle clips on the front brake pads; if faulty these can allow the brake pads to make loud rattling or clanking noises when going over bumps.
Brian
2006 X350 3.5 V8 Sport Premium in Midnight / Ivory
1969 Triumph Daytona rider
Previous XJs:
X350 2.7 TDVi in Westminster Blue / Barley
X308 4.0 V8 in Meteorite / Warm Charcoal
X300 3.2 in Spruce / Barley
XJ40 3.2 Sport in Gunmetal / Saville Grey

User avatar
J44EAG

Moderator
Posts:6239
Joined:Sat Oct 20, 2007 9:57 pm
Location:Warlingham Surrey/Faversham Kent

Re: What's that rattle?!

Postby J44EAG » Thu May 17, 2018 7:16 pm

A dull "bonk,thonk" is usually ARB bush wear.

"Click-clack" is usually the ARB to lower wishbone, vertical links. Prices are a humble £15-20 for each vertical link. So you can put four new links on the car for around £80. If you can get the car on ramp, then you don`t even need to remove the wheels. I usually cut through the nuts and threaded portion with an angle grinder fitted with a 1mm slitting disc. That takes about five minutes with another five minutes spent tightening the two nuts on the new link. You should be able to replace all links in less than an hour.

Hope that helps.

Mike
X350 Co-ordinator

2004 XJR

charlier6790

Member
Posts:39
Joined:Sun Mar 01, 2009 12:00 pm
Location:Hereford

Re: What's that rattle?!

Postby charlier6790 » Fri May 18, 2018 11:27 am

Brian/Mike, Thanks for your advice. I'll check-out both the vertical links and the anti-rattle clips on the front brake pads. Thanks again. Charlie

jimdox
Posts:25
Joined:Sat Mar 04, 2017 4:39 pm
Location:Clackmannan
Contact:

Re: What's that rattle?!

Postby jimdox » Sat May 19, 2018 8:47 pm

I have a rattle in the same area on my car also and last week discovered it is coming from the bracket that holds the air suspension compressor. There seems to be a small bush on this and mine is worn. I am going to attempt to get my front bumper off in the next couple of weeks to repair a parking sensor so I will try and do this at the same time.

charlier6790

Member
Posts:39
Joined:Sun Mar 01, 2009 12:00 pm
Location:Hereford

What's that rattle?!

Postby charlier6790 » Sun May 20, 2018 10:36 am

Thanks, Jimdox. I plan to check the anti-rattle clips on the disc pads first (as I'm planning to replace the front discs/pads anyway) and, if that doesn't do the trick I'll check-out the vertical links and the suspension compressor bracket. Regards. Charlie

jookul100431

Member
Posts:70
Joined:Wed Aug 07, 2019 12:00 pm

Re: What's that rattle?!

Postby jookul100431 » Wed Oct 02, 2019 8:16 pm

Hi Guys

I think I may have something similar but my only seems to come into the car when I travel on very bumpy potholed road at about 50 mph....are you getting your noises under similar conditions....

I got my from l ft shock replaced and that has help as I thought nk that shock was gone and so it's doing its job now...any final resolutions that worked for u guys

charlier6790

Member
Posts:39
Joined:Sun Mar 01, 2009 12:00 pm
Location:Hereford

What's that N/S/F rattle?!

Postby charlier6790 » Fri Oct 04, 2019 10:50 am

My garage tell me that an air conditioning pipe in the N/S/F wheel arch area (behind the wheel arch liner) has come loose and appears to be the source of the rattle. The garage has refitted the pipe to its bracket and, so far, the rattle appears to have gone. Let's hope they are right!

jookul100431

Member
Posts:70
Joined:Wed Aug 07, 2019 12:00 pm

Re: What's that rattle?!

Postby jookul100431 » Sat Oct 05, 2019 6:53 pm

I'm still try to ng to figure my out without success...I can recreate lots of rattles and knocks manually but nothing that sound like the problem I am having.....very fusterating


Who is online

Users browsing this forum: No registered users and 1 guest