Page 1 of 2
Fitting a trip computer
Posted: Thu Mar 30, 2006 6:00 pm
by Gordon@1962
I've a 1991 model with the old analogue clock in and was wondering if there would be any problems fitting a trip computer?
http://www.razey.karoo.net/images/TripComputer.jpg
Does anyone know if it is all wired up and I just need the parts, or if it is more complicated than that?
thx,

Posted: Thu Mar 30, 2006 6:32 pm
by poprivet
Your picture shows the model for 6 cylinder engines, the V12 has 2 white plugs. It is a project I tried a couple of years ago, the analogue clock and the computer use the same connector, of course the wood faced panel is different.
I couldn't get any fuelling information on mine, perhaps the computer was faulty as I couldn't locate any other missing interface anywhere. In the end I gave up and went back to the clock.
Pop
Posted: Thu Mar 30, 2006 6:51 pm
by Gordon@1962
Thanks Pop.
It is the 6 cyl and fuel information I'm after.
I think if I can get one cheap enough I might give it a go, but if there a bit pricey I don't think I'll risk it.

Posted: Fri Mar 31, 2006 4:03 pm
by apax
Hi Gordon@1962. It'll probably be about £20 on Ebay, but you MUST do some research on part numbers first, as there were different types in different years for different cars.
I have one going spare (part no. DAC 3749) which I bought because my computer wasn't working when I bought the car. Pulled out the existing computer and it wasn't plugged in!!!
Just as well really as, according to Pop's post, mine may be a V12 fitting as it has 2 white x 3 pin connectors. I was told it had come off an '87 3.6 but my car (3.6 cabriolet) has a single connector, as per your photo. This is why the research is vital.
Cheers, Archie.
Posted: Fri Mar 31, 2006 4:31 pm
by Gordon@1962
I've realised the one with the single blue conector is for the 6 cyl and the one witrh two whites ones is for the 12 cyl.
There were 2 on ebay. One for £20 for the 12 cyl and one for £10 for the 6 cyl.
I'd already started biding for the 6 cyl model and was in front.
But I got out bid by about 50p becasue I was late home.
All becasue I poppped into Halfords for some wax.
Never mind.
Regards
Gordon
Posted: Fri Mar 31, 2006 5:48 pm
by Jon
The one you want is with the blue connector, and yes it will plug straight in (did it on mine) if you can get hold of the veneer panels that is a bonus, alternately you could hack your single piece veneer down to size like we did

Posted: Fri Mar 31, 2006 6:28 pm
by Gordon@1962
Thanks Jon,
So all I need now is the one I need.

Posted: Sat Apr 01, 2006 3:07 pm
by Jon
Posted: Sat Apr 01, 2006 6:15 pm
by Gordon@1962
Nice.
I've asked the seller a few questions and if ok, I'm going to bid.
thx m8,

Posted: Sat Apr 01, 2006 11:28 pm
by apax
The answer to one of the questions is that it is from a V12!
You really do need to know the part number that applies to your car or you'll be shooting in the dark.
Cheers, Archie.
Posted: Sun Apr 02, 2006 10:30 am
by Gordon@1962
ah ha!
So you read my question on ebay.
I think one of the problems of buying second hand parts is that the sellers don't always know the part number.
I have what I thought was the right parts catologue for my car but part no. DAC 3749 in my book shows 2 white plugs comming out of the back, but if I want one to fit my car it will need 1 blue plug.
Do you think if I make sure it comes from a 3.6 coupe near to 1991 (Janaury) as possiobe and it has 1 single blue plug it will be ok?
Or do you think I need to get the right part number and buy one from a dealer who has the part number also?
If so either I need a new parts catologue or my car is a hybrid.
Regards
Gordon
Posted: Sun Apr 02, 2006 12:04 pm
by poprivet
There should be a metallic Jaguar sticker on the back of the computer with both the part number and a date code, for instance the one I have (for a 3.6) is DAC4452 and 2188 (indicating 1988) I would be very suspicious of any seller not being able to provide that sort of basic information.
There would be a difference between USA and UK computers due to the difference in size of gallons.
Pop
Posted: Sun Apr 02, 2006 12:42 pm
by Gordon@1962
Any ideas on how I would find out the part number I'd need for my model?
Its a 3.6 coupe registered 02/01/91.
VIN/Chassis number SAJJNAEC3CA175963
Posted: Sun Apr 02, 2006 8:06 pm
by Jon
There'll be no difference between pop's 1988 car and your 1991 variant as far as the trip comp. is concerned, so you're after a DAC4452.
I had previously thought that only the 3.6 cars had the blue connectors, as they facilitate the fault code readout not present on the V12 cars (these also have another box known as a fuel interface unit) but it seems I'm wrong!

Posted: Sun Apr 02, 2006 8:12 pm
by Gordon@1962
Thanks Don,
