Cruise Control

Moderators:davidr, BigCatXJS, dhdove

Graham

Member
Posts:135
Joined:Fri Jul 20, 2007 3:51 pm
Location:Nuneaton,Warwickshire
Cruise Control

Postby Graham » Tue Oct 03, 2006 10:27 pm

After successfully using the cruise control everyday on my 1996 Celebration model yesterday it refused to work.No indication of any problems were apparent the day before when i used her.Has anybody any ideas or had similar problems that may be able to help.Many Thanks Graham :(

User avatar
Mark_B
Posts:199
Joined:Wed Sep 07, 2005 7:05 pm
Location:Luton
Contact:

Postby Mark_B » Wed Oct 04, 2006 9:37 am

It's not just dicky switch contacts is it? (the rocker switch in centre console) The window and hood switches often get gummed up. Other readers should give suggestions also.

You know, diagnosing a cruise control in-situ is gonna be difficult to start with, because it only engages on when the car is above a certain speed. Wild ideas like supporting both rear wheels off the ground :!: (must be both, LSDiff remember) would work, BUT it's potentially very dangerous!

How the C/C works is there's a 5V pulse signal from the rear axle, via a small box in the boot, which is also associated with the speedo and the trip meter. There;s a ECU under the passenger seat and has the driver controls connected to it. Also connected to the ECU is wires going to the actuator on the engine that operates the throttle.

When ECU demand a speed increase, it powers the actuator vacuum pump motor, increases the throttle via the black contracting bellows as required, then the motor is deactivated. When there's a speed reduction demand, a valve opens as required to slowly vent off the stored vacuum. Also whenever the brakes are applied, another large valve vents all the vacuum at once. All these are 12V signals, and are polarity-sensitive. If you wanted to test the actuator in isolation you'd have to ensure the vent valve was powered otherwise the motor would whirr away without moving the bellows.

When I was commissioning my cruise control retrofit, I'd used a pulse signal generator to simulate the speed signal so I wouldn't have to run the engine.

Hope this is a help.

XJ-S 3.6 230k miles +

ptjs1

Member
Posts:3520
Joined:Thu Apr 27, 2006 7:14 pm
Location:Kent

Postby ptjs1 » Wed Oct 04, 2006 12:35 pm

Graham,

Mark_B has given a really good summary of the operation of the system. One area that I have found prone to failure on these systems is the vacuum operation of the throttle. A really simple test is to pull off the vacuum pipe and suck on it to see if the bellows holds. If it doesn't you've got a leak in the bellows somewhere or in the pipe.

Good luck,

Paul
1995 XJS 4.0 Convertible
1980 XJ-S Pre-HE
Jaguar 4.2 Supercharged engine (but not with a Jaguar body..)

Graham

Member
Posts:135
Joined:Fri Jul 20, 2007 3:51 pm
Location:Nuneaton,Warwickshire

Postby Graham » Thu Oct 05, 2006 7:26 pm

Hi both many thanks for your info, i have taken out the switch and cleaned the contacts but to no avail.I ahve changed the fuses also but no luck.I have detached the pipe from the vacuum unit and sucked on the pipe and i get a whistling sound coming back through actuator pump.I am not sure where the bellows are on my system as it seems to be a sealed unit next to the relays on the passenger side inside the bonnet.Is this where the bellows are situated?I use my xjs everyday with a lot of motorway driving so the loss of the cruise control is a great shame.Thanks again Graham

ptjs1

Member
Posts:3520
Joined:Thu Apr 27, 2006 7:14 pm
Location:Kent

Postby ptjs1 » Fri Oct 06, 2006 10:01 pm

Graham,

I think you might be referring to the vacuum pump which is located on the inner wing by the relays.

The bellows is oft referred to as the throttle actuator and is mounted on the end of the throttle actuator linkage rod. I have emailed you a copy of the page from the service manual which shows its position. Hope this helps.

Regards,

Paul
1995 XJS 4.0 Convertible
1980 XJ-S Pre-HE
Jaguar 4.2 Supercharged engine (but not with a Jaguar body..)

User avatar
Mark_B
Posts:199
Joined:Wed Sep 07, 2005 7:05 pm
Location:Luton
Contact:

Postby Mark_B » Fri Oct 06, 2006 10:45 pm


A really simple test is to pull off the vacuum pipe and suck on it to see if the bellows holds. If it doesn't you've got a leak in the bellows somewhere or in the pipe.
Paul


Just like to add, remember to suck on a pipe going straight to the bellows, not the pipe that's from the vacuum pump !. This is because the vent valve (energised to close) next to the pump will be letting out the vacuum as fast as you suck it!
XJ-S 3.6 230k miles +

Graham

Member
Posts:135
Joined:Fri Jul 20, 2007 3:51 pm
Location:Nuneaton,Warwickshire

Postby Graham » Sat Oct 07, 2006 8:23 pm

Many thanks for your help everyone for trying to sort out my cruise control problem.I have tried the "suck" test and the bellows appear to be holding.I have recieved a reply from Dave Marks who has suggested a possible different cause in that the dump valve could be set to open therefore not generating enough pressure for the cruise control to work.He has also suggested i check the fuse on this first.As soon as i have managed to get the time to check these options i will post back also.If this fails it looks like Markb's technical route i will have to follow oh dear!!Many thanks again this forum is worth its weight in gold.Graham

User avatar
Mark_B
Posts:199
Joined:Wed Sep 07, 2005 7:05 pm
Location:Luton
Contact:

Postby Mark_B » Mon Oct 09, 2006 11:49 pm

Just thought of a wild idea for diagnosing problem. Perhaps this could be a cut out and keep thing to put in a scrapbook :-)

Get yourself 3x 12V small lamps, say 2.2W perhaps in holders that you can attach wires to. Get some bell wire. Connect 3 longish bellwire pairs across each the actuator items: 1-little valve, 2-motor, 3-big dump valve, perhaps via (6) safety-pins poked through the wire to make the connections, or poked into the connectors somehow. Have the other ends wired to the 3 light bulbs, perhaps poked through a bit of cardboard where you can see it, labelled accordingly.

Then while driving engage CC and look at the lights:

1.small valve lamp= goes out to decelerate, else on
2.motor lamp = goes on to acellerate, else off
3.dump valve lamp= on (or is it off?) when brakes applied, (there's a switch for it next to brake light and I think there's another swithc on this circuit to do with the gearbox or clucth or something.

For example what you should see is #1 on, with #2 blinking as required when starting up an incline or resuming, and when going down an incline #2 is off and #1 blinks off as required. When on straight #1 on, #2 off.
XJ-S 3.6 230k miles +

keithmervyn
Posts:28
Joined:Sun Sep 11, 2005 11:28 pm
Location:Stockport, Cheshire

Failed Cruise Control

Postby keithmervyn » Thu Oct 19, 2006 11:00 pm

I've just read your problem. The C/C on my 4.0 Convertible used to randomly, mostly permanently, fail over most of a two year period and drove me scatty.

I use a well experienced Jag auto-electrician at Elite Cars, Independant Jag servicers, Stockport (0161 442 1994), called Phil. It drove him scatty too, but he was always convinced that the problem was basically electrical, and after 2 long years of his intermittent trial, error and fiddle, I think he rewired the appropriate fuse unit (under passenger seat) and handbrake switch, and everything started working and has now been solid for over a year.

He was always able to simulate the complete operation electrically on his voltmeter without the car being "driven".

Phil is a very pleasant and helpful guy, if you mention my name (Keith Roberts) he will remember the saga, and may well prove helpful to you.
Keith MR

Graham

Member
Posts:135
Joined:Fri Jul 20, 2007 3:51 pm
Location:Nuneaton,Warwickshire

Cruise Control

Postby Graham » Tue Aug 07, 2007 5:11 pm

Well after all this time trying different diagnosis on the cruise control in desperation i put in a new switch and hey presto it now works. Thanks for all your help with travelling over 23000 miles in my celeb this last year my foot was starting to ache.Graham



Who is online

Users browsing this forum: No registered users and 2 guests