Page 1 of 1

Fuel Filters

Posted: Sun Mar 19, 2017 11:04 am
by Tintin
A previous owner of my 4.2 Series 1 replaced the original fuel filter set up with two canister filters in the boot, one upstream of each of the two pumps. These are physically quite large and sit in a limited space. In conjunction with hose and fuel line modifications outlined in another thread I want to change these filters for smaller units to achieve a neater layout using less hose. I assume the large size allows high flow rates at low pressures but I have no idea if they are oversized for the application and can be changed for something smaller without over stressing the pumps or causing fuel starvation. The filters I want to change are MAHLE KL9's 165mm overall long (including the 8mm hose stubs) and 75mm diameter.

Can anyone give any advice please?

Robbie

Re: Fuel Filters

Posted: Sun Mar 19, 2017 10:22 pm
by oldtimer
Hi Robbie,
You could use an AC filter assembly Part No C38490 which houses a disposable filter element Part No JS 660 used as standard fitment on a Series 2 XJ12. It's a neat job , cast alloy head with bulkhead mounting lugs and two threaded fuel pipe connections. The filter element fits into a chamber with a single securing bolt up through the centre into the cast alloy head. In my case it is fitted into the back right hand corner of the spare wheel space. It has the fuel flow capacity for the V12 so will be adequate for the 4.2 litre model.

This filter assembly would fit into a cube about 3 x 3 x 3 inches

I have been considering your proposal to delete hose pipe length in the boot/ fuel pump area in favour of rigid metal pipe. I can see the logic of that but I am concerned that this process will increase the number of joints in the line and outweigh the benefit of less rubber pipe.
Others reading this need to refer to Robbie's important previous thread about petrol fumes in the boot and the effects of Ethanol on hoses.

Oldtimer

Re: Fuel Filters

Posted: Mon Mar 20, 2017 2:03 pm
by Tintin
I would prefer to have the filters upstream of the pumps to protect them from tank debris, and I think the unit your are suggesting OT is fitted downstream of the pumps. I have found a Sytec filter which is slightly smaller and has the additional benefit of a cranked outlet stub; the supplier says this is suitable for use pre-pump so it may be OK. BFS (where I bought the pumps) offer a small in line filter with replaceable element which I will consider as an alternative.

I am using 8mm ID copper pipe with end feed soldered joints for the metal fuel lines but even so the metal line/pump and metal line/filter connections need short lengths of hose with pipe clamps. You are correct that every hose joint is a potential weak point; nevertheless, the hose surface area will be vastly reduced and the fuel vapour issue thereby minimised.

I will post a conclusion when I have finished the installation - in the meantime I have a serious and unexpected oil leak to sort out; it seems to be coming from the spin on filter adaptor (another previous owners modification). Hopefully it is only the seals.

Robbie

Re: Fuel Filters

Posted: Mon Mar 20, 2017 3:15 pm
by J44EAG
I`ve been involved with re-fitting boats for years and have been obliged to plumb systems with ISO 7084 specification flexible fuel hose.

7084 is the minimum standard acceptable for MCA, Lloyds A1 and the Inland Waterways Boat Safety Scheme. If I do not see a 7084 installation, I will advise a customer to let me rip out the existing often diabolical rats nest!

7084 is fire resistant and also E85 Ethanol suitable. It is good stuff and it can be sourced in various sizes from local chandlers, marine wholesalers such as ASAP Supplies and Aquafax.

Here is a link.https://www.google.co.uk/url?sa=t&rct=j ... Gg&cad=rja

I`ve always installed any filter arrangement before a fuel pump. This guards against tank crap being drawn into the pump and lodging on the suck and blow poppet valves frequently found in fuel pumps. I believe it is beneficial to fuel flow not to filter after the fuel pump where inclusion of a filter could cause fuel blockage issues if the filter were to block up with crud. Consistent fuel pressure is likely to be maintained from the pump to injection distribution pump units, injectors or carburettors.

Old flexi fuel pipes can cause huge issues. My pal has a pair of large lorry sized, somewhat ancient six cylinder Perkins engines in his fast motor boat. A year ago, one engine suddenly refused to start. We ascertained that suction and pressure fuel pipes were not leaking. Dave went on to have a new lift pump, a reconditioned metering pump, serviced injectors and some new ISO7084 fuel tube. Nine moths later, it still refused to start except on a separate fuel can supply. I suggested a flexi fuel pipe issue in some deeply buried location. We lifted the engine and gearbox on the yard crane to get better access. Sure enough, a three inch section of evil old pipe was discovered. It partially collapsed under fuel lift pump suction but we also surmised it was porous and letting in air. The fuel pipe system was re-worked, engine dumped back down, the fuel system bled and the engine started at first turn of the key. That job had four guys looking the job with in excess of 160 working years experience between us. Even then, it took nine months to sort the issue. Don`t put joints in pipes in obscure locations!

Mike K

Re: Fuel Filters

Posted: Mon Mar 20, 2017 4:29 pm
by Tintin
Thanks, Mike - useful info, direct and to the point as always!

Novaflex 360 has a permeation rate of less than 15g/sq m per day, so as far as vapour emission is concerned it meets the same criterion as SAE J30 R9.

Happy to say that the oil leak was an easy fix - the threaded spigot fixing for the adaptor block had worked loose.

All ready to roll again!

Robbie

Re: Fuel Filters

Posted: Mon Mar 20, 2017 10:12 pm
by oldtimer
Tintin,
The crucial point that you have identified is in regard to a suitable rubber hose pipe . Hopefully you will have eliminated the perpetual stink of petrol in the boot. As regards to filtration, both tanks have a fine gauze filter on the end of the pick up pipe in the fuel tank (Part No C29445)
These can be accessed by removing the tank drain bung through the aperture in the rear quarter panel - this hole may be closed off with a rubber/ plastic bung.
You will recall I replaced pipes and overhauled pumps not so long ago and at the same time examined said filters. Despite not removing them for many years they were as clean as a whistle. Of course if the tanks are heavily corroded the solution is to replace the tanks as filters will simply block up at some stage.
The standard arrangement of filtration both before and after the pumps has served me well and see absolutely no reason to alter this in order to try and disguise some other defect. I fully endorse your discovery and introduction of a suitable Ethanol compliant hose but would not entertain the idea of introducing additional joints.

Oldtimer

Re: Fuel Filters

Posted: Tue Mar 21, 2017 2:56 pm
by Tintin
That's interesting. When I took the off side tank out, I found that my fuel supply pipe connection from the tank was a simple pipe and olive connection (no filter visible) into a threaded fitting near the base of the tank, some distance to the rear of the drain bung. If the filter is in the drain bung there must be an internal tank pipe connecting the two?

Robbie

Re: Fuel Filters

Posted: Tue Mar 21, 2017 6:49 pm
by oldtimer
Tintin,
I don't know, what I do for you ! Yes you are quite right, the tank external fuel pipe which connects the tank to inside the boot Part No C36561 is a simple coupling.
The drain bung to which I referred is a large brass bung with a small bolt in the middle. Removal of the centre bolt allows the tank to be drained in a regulated fashion. Remove the large brass bung and you will have the contents of the tank in your lap in one huge flood.
Yes there is a short length of internal pipe from the external coupling which is formed to point down into the centre of the brass bung. With the tank installed in the vehicle it is best examined with a flame proof torch looking up. You should see the fine gauze filter pushed onto the pipe end.
This bung is the same as that fitted to my 1956 Mk 7M. During that period it was a much larger course mesh brass filter. I owned my Mk 7 back in the late fifties but would you believe I happen to have one of those filters and bungs on the bench which I shall show you.
I'm interested to know how you drained the tank when you recently removed it ?

Are you going to make Kemble this month, if so I'll bring along some parts book for you to see for yourself

Oldtimer

Re: Fuel Filters

Posted: Wed Mar 22, 2017 2:57 pm
by Tintin
Thanks for that useful info OT. I assumed the tank filter (if any) would be on the outlet connection, not on the drain plug - that would be logical. I drained the tank by removing the drain plug in the bung, but didn't remove the entire bung itself so didn't see the filter you describe - or receive the free petrol shower!

The system was previously modified by fitting canister filters between the tanks and pumps and given the advances in filter technology over the last 40 years I am inclined to retain them in principal but renew them as a service operation (but possibly with smaller ones) - I can't see that any harm would result.

The R9 hoses greatly reduce vapour permeability but do not eliminate it completely (15g/sq m per day) so reducing hose length is also of benefit. In principal I agree that joints are a potential weakness in any plumbing installation but if correctly and carefully made the risk is small - and some joints are essential for maintenance and to replace filters and pumps occasionally.

Robbie

Re: Fuel Filters

Posted: Mon Mar 27, 2017 5:57 pm
by Tintin
Well, that didn't go as planned at all!

I fitted R9 hose which was an improvement but by no means a cure for hose permeability. Further research turned up Gates Barricade hose which I have now fitted and does appear to have cured the problem of fuel vapour in the boot. The following link to the Gates site may be of interest when choosing fuel hose for any particular application:- http://www.gmcmhphotos.com/photos/data/ ... _Final.pdf

Robbie

Re: Fuel Filters

Posted: Tue Mar 28, 2017 2:17 pm
by stevewarbs
Hi Robbie

I was about to buy some fuel hose from the local factors when I saw your post and want to take your advice and use the barricade hose. So far I can only find it on ale at Moss, where did you buy your from and do you kno offhand if I need the 6mm or 8mm

Regards
Steve

Re: Fuel Filters

Posted: Tue Mar 28, 2017 4:52 pm
by oldtimer
Steve,
As I'm sure you will know our cars measurements where described in Imperial sizes. So 6mm = 1/4 inch and 8mm = 5/16 inch.
During the above conversations with Robbie hose size was never mentioned , it is only you mentioning that jogged my memory and I certainly used both sizes on the carb version V12 , but that is a slightly different layout.

I was not fully aware of the Ethanol problems that Robbie has identified and simply bought the necessary from Stevenson's who usually display at the NEC and Stoneleigh .
Robbie recently checked out these hoses on my car with his new magic wand and did not find any fault which I was relieved about.

For the boot area I selected a cotton braided hose, only because it looked pretty and stainless steel braided hose under the bonnet (as it was originally) I also bought size to match, rubber boots which fit over the end of each hose and contains the cotton or metal braiding with a clip holding it neatly in place

Hope that helps a little
Oldtimer

Re: Fuel Filters

Posted: Tue Mar 28, 2017 6:38 pm
by stevewarbs
Thanks OT, it is 5/16 in the boot of mine and 1/4 under the bonnet. I think any new hose would be better that what I have currently and should get rid of the awful smell but as the hose Robbie has used has way better spec than anything else I can find I may as well go for that. Also, the R9 spec of 15g/sqm is based on 5% ethanol and could increase as ethanol levels increase whereas the 1g/sqm of the Barricade appears to be a fixed figure.

Re: Fuel Filters

Posted: Tue Mar 28, 2017 8:01 pm
by Tintin
HI Steve

Sorry to have missed you at Stoneleigh - OT and I were both there and I treated myself to a front wing and a rear quarter valence panel. Only need the other side now!

As OT says, the correct imperial size for boot hose is 5/16 inch; when converted that gives 7.9mm which I think is close enough to 8mm for all practical purposes.

I got my hose from Moss in Bristol - part no GFH1031X. They don't do all sizes and all applications, but do have the size for the boot installation for the S1.

Good luck!

Robbie

Re: Fuel Filters

Posted: Thu Mar 30, 2017 5:25 pm
by stevewarbs
Thanks Robbie, ordered from Moss.