Page 1 of 1
1966 3.8S Vacuum pipe
Posted: Tue Mar 01, 2022 10:43 pm
by brent
Howdy all,
Hoping another S-type owner can help me out, there is a vacuum pipe that runs from the brake booster to a resevoir on the other side of the car. This was missing on mine and I managed to source a pipe but cannot figure out exactly where it should be attached.
Would anyone be able to help with advice or a photo?
Cheers!
brent
Re: 1966 3.8S Vacuum pipe
Posted: Sun Mar 27, 2022 10:10 pm
by steve.pritchard146
Hi there, it runs along the front cross- member.
Mine is in very poor condition but I will try to get some pics tomorrow
Regards
Steve
Re: 1966 3.8S Vacuum pipe
Posted: Mon Mar 28, 2022 1:35 pm
by steve.pritchard146
Ok here we go hopefully this is clear (just ignore all my rusty~ness! ) there are two small brackets attached with self tappers to the front cross member. Shout if it’s not clear and I can take more pics as I’m in the process of dismAntling and replacing the areas around this which will necessitate removing both the vacuum chambers.
Re: 1966 3.8S Vacuum pipe
Posted: Mon Mar 28, 2022 1:36 pm
by steve.pritchard146
Hmm pics didn’t attach
Re: 1966 3.8S Vacuum pipe
Posted: Thu Mar 31, 2022 4:34 pm
by brent
Thanks Steve, that's fantastic, I think I can work out which end goes on which side as well now

Re: 1966 3.8S Vacuum pipe
Posted: Fri Apr 01, 2022 8:05 am
by steve.pritchard146
No probs,
I’m very much in dismantle stage at the moment- trying to someone the courage to cut of the (remains of) the front cross member and various supporting stays, I will need to remove both vacuum tanks and many photographs are the only chance I have of remembering how everything fits!
Mine is an S-Type but happy to help if you need anything else
Re: 1966 3.8S Vacuum pipe
Posted: Thu Apr 21, 2022 2:14 pm
by brent
Mine is an S as well
I wish I had the courage to do some welding, I removed the pipe today and will try and mount it properly now. The check valve on the vacuum cylinder came apart so I guess I now have something else to buy!

Re: 1966 3.8S Vacuum pipe
Posted: Thu Apr 28, 2022 1:47 pm
by steve.pritchard146
yes the list of parts to buy is currently endless.
I'm trying to divide my car into project areas so as not to be overwhelmed by something dismantled never to be re-assembled.
Unfortunately to repair the area of the front chassis that is corroded I need to disassemble quite a bit...
Re: 1966 3.8S Vacuum pipe
Posted: Fri Apr 29, 2022 1:04 pm
by B87UL
Brent
The tank on the opposite side to the brake booster is for the heating system controls, as you are probably aware.
It is some years since I re-piped the vacuum circuit on my S Type but in order to protect the brake booster vacuum I fitted two shut off valves in circuit adjacent to the brake booster. These were arranged to isolate either the brake booster vacuum or the heater vacuum and can be a very useful tool.
These enable me to isolate the system down stream of the brake booster, or the booster itself, if at any time the heater system vacuum, or booster became open circuit, by either tank leak, connection or valve failure.
The valves are useful if you suspect loss of vacuum is causing engine idling problems and need to isolate parts of the system. It is a cheap method of ensuring the brake vacuum circuit can always be secured, and also tested, and might be a consideration for you.
Memory is weak, but I seem to remember also replacing the steel front end cross feed pipes with correct type rubber vacuum hose. Be aware to use correct vacuum hose on these circuits, pressure type hose does not necessarily mean it is rated for vacuum.